Plumbing for Beginners: The Essentials for Installing a Bathtub
Plumbing for Beginners: The Essentials for Installing a Bathtub
Blog Article
On this page below you will find a good deal of amazing additional info related to A Step-by-Step Guide to Installing a Bathtub.
Setting up a tub isn't exactly rocket science, yet it does need strong plumbing, woodworking, as well as occasionally, tiling abilities. Replacing an old tub with a new one is also a moderately challenging task. If the old tub is readily available, the project can relocate immediately; if you have to open a wall surface to eliminate the old tub and position the brand-new tub, the job is a lot harder. In either instance, the project is within a house handyman's skills, although you will certainly require a helper to vacate the old tub and also set in the new one. Make sure you have actually certified on your own for the job as well as fit attempting it. Rather than hiring a service provider to take over a halfway-completed project, it is far better to consider employing one before you begin. Opportunities are you may need an expert plumber to make tube links.
This short article will certainly aid you set up a brand-new tub in your restroom if you have already acquired a brand-new bathtub as well as don't need to change the plan of your previous water supply pipelines.
Your devices and material list ought to consist of the following:
Removing Old Taps
If you require to change old faucets with brand-new ones as a part of your setup, after that the first thing you should do is detach the water system. After doing so, turn on the faucets to drain pipes any kind of water remaining in the system. The process of removing the existing faucets can be quite troublesome because of the restricted access that is usually the instance.
Make use of a basin wrench (crowsfoot spanner) or a tap tool to undo the nut that attaches the supply pipes to the taps. Have a towel ready for the remaining water that will certainly originate from the pipes. As soon as the supply pipelines have been removed, utilize the exact same tool to loosen the nut that holds the faucets onto the bath/basin. You will require to stop the single taps from transforming throughout this procedure. As soon as the taps have actually been gotten rid of, the holes in the bath/basin will need to be cleaned of any kind of old securing compound.
Before proceeding to fit the brand-new faucets, contrast the pipeline connections on the old faucets to the brand-new faucets. If the old taps are longer than the new taps, after that a shank adapter is required for the brand-new faucets to fit.
Suitable New Taps
If the tails of the new faucets are plastic, then you will certainly require a plastic port to avoid damages to the string. One end of the adapter fits on the plastic tail of the tap and the other end offers a connection to the current supply pipes.
If you need to fit a monobloc, after that you will require reducing couplers, which connects the 10mm pipeline of the monobloc to the basic 15mm supply pipeline.
Next off, place the faucet in the placing hole in the bath/basin making certain that the washing machines remain in area between the tap as well as the sink. Secure the tap in place with the supplier given backnut. As soon as the tap is safely in place, the supply pipes can be linked to the tails of the taps. The faucets can either be linked by using corrugated copper piping or with typical faucet connectors. The previous kind ought to be linked to the tap finishes initially, tightening up just by hand. The supply pipes can later on be linked to the various other end. Tighten up both ends with a spanner after both ends have actually been linked.
Setting up the Tub
Making use of both wooden boards under its feet, put the bathtub in the called for placement. The wood boards are practical in equally spreading out the weight of the tub over the location of the boards instead of concentrating all the weight onto four small factors.
The following objective is to ensure that the bath tub is leveled all round. This can be accomplished by examining the spirit level as well as changing the feet on the bath tub till the level reviews level.
To set up faucets, fit the bottom of the furthest versatile tap adapter to the proper supply pipe by making a compression join; after that do the same for the various other tap.
Switch on the supply of water and check all joints as well as new pipework for leaks and tighten them if essential. Load the bath tub and also examine the overflow electrical outlet and the typical electrical outlet for leakages.
Finally, take care of the bath paneling as explained in the supplier's user's manual. Tiling and also sealing around the tub needs to wait till the tub has actually been utilized at least when as this will certainly settle it right into its last placement.
Preparing for the Setup
First of all, the supporting framework supplied with the bath should be fitted (if called for) according to the manufacturer's directions. Next off, fit the faucets or mixer to the bath tub. When suitable the tap block, it is necessary to make certain that if the tap comes with a plastic washing machine, it is fitted between the bathroom and the faucets. On a plastic bathroom, it is additionally reasonable to fit a sustaining plate under the faucets system to prevent pressure on the bathtub.
Fit the versatile tap connectors to the bottom of both faucets using 2 nuts and also olives (often supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and after that pass the electrical outlet with the hole in the bathroom. Use the nut provided by the producer to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the adaptable overflow pipeline to the overflow outlet. Afterwards, screw the pipeline to the overflow face which should be fitted inside the bath. Make certain you use all of the provided washers.
Link the catch to the bottom of the waste electrical outlet on the bathtub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Connect the bottom of the overflow tube in a comparable manner.The bathroom should now be ready to be suited its last setting.
Tiling Around the Bath tub
In the location where the bath satisfies the tile, it is needed to seal the accompanies a silicone rubber caulking. This is necessary as the fitting can move enough to break an inflexible seal, creating the water to penetrate the wall in between the bathroom as well as the tiling, leading to problems with wetness as well as feasible leaks to the ceiling listed below.
You can choose from a range of coloured sealants to blend in your fixtures and fittings. They are marketed in tubes and also cartridges, and are capable of securing spaces as much as a size of 3mm (1/8 inch). If you have a larger space to load, you can load it with twists of soaked newspaper or soft rope. Keep in mind to always load the tub with water prior to sealing, to enable the movement experienced when the bathtub remains in use. The sealer can crack rather very early if you do not take into consideration this activity before sealing.
Alternatively, ceramic coving or quadrant tiles can be utilized to border the bath or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are also conveniently available on the marketplace. It is a good idea to fit the floor tiles utilizing waterproof or waterproof sticky and also grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
We had been introduced to that report on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround through an acquaintance on our other blog. Do you know about another individual who is very much interested in Installing A Bathtub? Why not promote it. I enjoy reading our article about How to Install a Bathtub Yourself.
Plumbing challenges? Professional solutions await. Report this page